SOANAR ULTRASONIC ANTIFOULING UNIT
AUSTRALIAN MADE
LIMITED OFFER: FREE UPGRADE TO FREE SHIPPING OUTSIDE AUSTRALIA, USE COUPON CODE: FREESHIPANTIF
Protect your boat against barnacle and algae growth with the SOANAR Ultrasonic Antifouling System
* This is a 4 Channel antifouling system, suitable for boats up to 20m/65ft. We also have 2 Channel unit that is suitable for boats up to 14m/45ft.
FEATURE POINTS
• Helps keep the hull of your boat clean and free from most marine growth
• Reduces drag and increases your fuel economy
• Frequency of slipping for antifouling treatment is reduced enormously
• Typically cheaper than a slip, clean and antifouling paint job
• Safe for the environment, no harsh chemicals involved
AUSTRALIAN MADE
Designed, developed and manufactured in Australia. Australian ingenuity and quality.
INTRODUCTION
The SOANAR Ultrasonic Antifouling System is designed to largely replace the messy, expensive and dangerous antifouling chemical paints that you have had to use in the past to prevent marine growth.
In ideal conditions the SOANAR Ultrasonic Antifouling System will work without any antifouling paint. Marine growth activity can be very aggressive is some areas however. In such cases the SOANAR Ultrasonic Antifouling System works best when installed after a fresh hull clean and new antifouling paint job.
Be assured, however, that the SOANAR Ultrasonic Antifouling System will add years to an antifouling paint job no matter how hostile your marine environment!
MARINE GROWTH ON BOAT HULLS
Marine organisms will attach to virtually any underwater surface if that surface remains immobile for even a short amount of time, e.g. after one week marine growth will start. Marine growth typically attaches to your boat hull to catch tiny organisms that drift by from tidal activity. Left alone the underside of your boat will look like it has a thick, green carpet installed!
Normally a hull is painted with a product called antifouling paint to prevent this from happening. Not so long ago, antifouling paint had some pretty nasty things in it to deter marine organisms from settling on your hull. Unfortunately it was found that these chemicals fell out of the paint and entered the environment, and were deadly to oysters, mussels and other marine life. These chemicals were banned.
Today’s antifouling paint has far more benign chemicals (which are less effective) but operate in a slightly different way. When the marine organism attaches to the hull (and therefore the paint), the paint sloughs off (i.e. flakes off) taking the organism with it. Of course this only works for so long before you need to apply a new coat of antifouling paint.
HOW THE SOANAR ULTRASONIC ANTIFOULING SYSTEM WORKS
Inside the main control box is a specially programmed microprocessor which centrally controls the system, sending out a range of ultrasonic pulses with varying frequencies to the external transducer units. These transducers are attached with epoxy to the inside of the vessel’s hull, transferring the ultrasonic pulses directly into the hull. The hull then vibrates in tune with the ultrasonic wave pulse, making for a rather hostile and unpleasant environment for the marine growth. Indeed, it would be like trying to go to bed in the front row of a heavy metal concert!
You generally do not need to have the boat out of the water for installation. The transducer is installed on the inside of the hull
The ultrasonic pulses are outside the range of human hearing, and are attenuated after about 10 metres through water. If your boat is in a pen the boats each side may partially benefit from reduced growth as well!
Power is supplied by 12VDC, making wiring installation easy. A low voltage cut-out feature is also included, which protects the boat’s batteries from being over discharged. As you can see by the technical specifications table, this unit could flatten your battery bank given enough time with no recharging. It is ideal if your boat is in a pen with AC shore power constantly charging your batteries. If you are on a mooring without shore power, we strongly recommend wind or solar charging.
>>> Download INSTALLATION MANUAL
SPECIFICATIONS:
• 12VDC
• Suitable for power or sail
• Works with aluminium and fibreglass boats (not suitable for timber, ferro cement or fibreglass foam sandwich construction)
• Could be powered by a solar panel/wind generator
• Power consumption:
* 2 CH model: Daily power consumption: 18.2Ah; Average current draw: 750mA; Peak current draw: 5.5A
* 4 CH model: Daily power consumption: 28.8Ah; Average current draw: 1.2A; Peak current draw: 8.2A
• Low voltage cut-out: 11.8V
• Current draw in cut-out mode: <6mA
• Control box rating: IP65
• Transducer rating: IP67
• Power cable length: 5m
• Transducer cable lengths: 10m
• Control box dimensions: 171 x 121 x 55 mm
• Transducer dimensions: 70 x 70 x 71 mm
Unit is suitable for use on steel, aluminium and fibreglass boats hulls, it is suitable for the following:
Alaska, Angel, Bayliner, Bavaria, Bertram, Blackwatch, Cabo, Caribbean, Carver, Cheoy Lee, Clipper, Cresta, Deep V, Dominator, Dyna, Fairlane, Fairline, Fairway, Four Winns, Genesis, Grandbanks, Hampton, Hatteras, Horizon, Integrity, Island Gypsy, Kevlacat, Kingfisher, Kingston, Larson, Maritimo, Markline, Mariner, Meridian, Montefino, Mustang, New Ocean Yachts, Outer Reef, Pacific, Precision, Princess, Ramsay, Randall, Ranger, Regal, Riviera, Salthouse, Sea Ray, Sea Line, Silverton, Southern Cross, Sunseeker, Viking Vitech, Wellcraft, Whittley, Whitehaven and many more
NOTE: Larger vessels can simply use multiple units. Twin hull vessels will require double the recommendations above. For vessels with sandwich hull construction, refer transducer installation section in the User Manual for more detail on installation method.
|
